Implicit Motor Learning in Parkinson's Disease.

Objective: This study examined whether disruption of performance is moderated in Parkinson's disease (PD) patients who acquire their motor behaviors in an implicit manner. Method: Twenty-seven patients with PD learned a hammering task in errorless (implicit) or errorful (explicit) conditions and were tested for robustness of motor performance under a secondary task load, which required them to continuously count backward as they performed the hammering task. Results: Patients in the errorless (implicit) motor learning condition exhibited robustness to secondary task loading, whereas patients in the errorful (explicit) motor learning condition did not. Conclusions: Implicit motor learning techniques should be considered by PD rehabilitation specialists in cases in which existing disruption to movements is exacerbated by conscious control. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

基于CAN总线的舵机控制系统设计

主要介绍了一种基于CAN总线的舵机控制系统。系统以CAN总线作为通信方式，PWM控制信号通过硬件方式产生，具有结构简单、信号稳定和实时性强的特点。     

高压变频技术在油田注水系统中的应用与节能分析

油田注水系统的耗电量一般占整个油田生产耗电的40％-60％,因此降低注水系统的能耗可显著降低油田的生产成本。常规的通过调节阀门开启度来达到调节注水泵出口压力和流量的作法,会使很大一部分能量造成浪费,要解决这个问题,可以采取对注水泵进行调速的方法。文章论述了通过高压变频技术对注水泵进行调速,从而达到节能效果的基本原理;对一台恒速泵和一台变频调速泵并联运行时的效率进行了分析,并对应用实例进行了计算,注水站的效率比原来提高了9．04％,收到了显著的节能效果。     

钻机用集成化液压源的研制

针对当前钻机液压配套设备越来越多的趋势,研制了集成化液压源。集成化液压源不是把原有的几个液压源的叠加组合,而是实现了液压源电气就地控制和远程控制、流量集中控制分配,压力集中控制,形成多种输出流量、多级输出压力和多个输出端口。     

井下注剂用小直径管起下装置的研制

针对目前国内小直径管井下注剂设备配套工具不完整,不能满足现场使用要求的情况,研制了井下注剂用小直径管起下装置。该装置采用可正反向旋转的液马达驱动主轴的方案,通过同步齿轮带动链条,夹紧机构使链条上的夹块夹住小直径管,由液压系统实现整个操作与控制,从而使装置上下运动。井场模拟试验表明,井下注剂用小直径管起下装置可完全满足小直径管起下作业的要求,且可避免小直径管管体的变形和损坏。     

液力联轴器喷油着火事故的原因分析及预防

以矿用液力联轴器为研究对象 ,阐明其喷油着火的机理 ,分析其喷油着火的原因并作出事故树分析 ,针对现场使用的情况 ,提出预防措施及发展趋势 ,对矿井安全生产具有指导性作用。     

两相异步电动机变频调速装置

主要讨论对称两相变频器主电路的结构以及介绍一种简单实用的磁链轨迹控制技术．     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

液压伺服马达拖动研究

液压伺服马达拖动和液压伺服加载 ,目前列为液压技术研究的前缘学科。本文专门从液压伺服马达进行探讨。     

开关磁阻电机调速系统在煤矿井下的应用

随着开关磁阻电机的调速控制系统日臻完善，因其优越性能使得在各行业得到迅速推广，但在煤矿井下的特定环境中使用该调速系统仍存在着诸多问题有待分析研究。